Quintic Ball Roll v3.4 : System / Memory Specification (Windows 7, Windows 8, Windows 10) USB3 Camera Capture
Please Note: We would recommend using a designated computer for Quintic Ball Roll (i.e limiting the amount of additional software programs running)

• Intel i7 Processor: 3rd Generation (Ivy Bridge or newer), 8GB RAM.
• Hard Drive:
  • SATA HD Drive Speed: 7200RPM (A Solid State Hard Disk is recommended!)
  • HD Write Speed: Single Camera: 100 mb/s minimum
  • Connectivity: 1 or 2 x USB3 ports
  • Minimum Monitor Resolution: 1280 x 1024
  • Windows 7 or newer
• Please note: It is recommended to run your computer in 'Maximum Performance' or 'High Performance'. This can be set within the power management options within Control Panel. Quintic Ball Roll has a lot of processing to do so eco-modes, for example battery saving / energy saving / balanced / maximise battery life, can restrict functionality particularly when on battery power.

Quintic High-Speed Camera : 64bit Quintic USB3 High-Speed Camera - 4.90 Driver
(Windows 7, Windows 8, Windows 10) - November 2017

• Double click the 64bit Quintic USB3 High-Speed Camera Driver
• Complete Installation
• Please refer to the Quintic USB3 Camera Installation Guide.pdf
• Supports USB 3 cameras for Windows 10, 8, 7.

64bit Quintic USB3
High-Speed
Camera Driver

Quintic High-Speed Camera : 32bit Quintic USB3 High-Speed Camera - 4.90 Driver
(Windows 7, Windows 8, Windows 10) - November 2017

• Double click the 32bit Quintic USB3 High-Speed Camera Driver
• Complete Installation
• Please refer to the Quintic USB3 Camera Installation Guide.pdf
• Supports USB 3 cameras for Windows 10, 8, 7.

32bit Quintic USB3
High-Speed
Camera Driver

Quintic Ball Roll v3.4 : January 2017 (Windows 7, Windows 8, Windows Ten)
Quintic USB3 High-Speed Camera - Club & Ball Data / Launch Angle / 3D Initial Spin / Address Position vs Impact

• BEFORE INSTALLING THE QUINTIC BALL ROLL SETUP, YOU MUST INSTALL THE COMPLETE QUINTIC HIGH-SPEED CAMERA DRIVER (32 / 64 BIT) IF INSTALLING FOR THE FIRST TIME (SEE ABOVE) - Please note, if you are only updating the Quintic Ball Roll software you do not need to install the camera drivers (they should already be on your machine)

• Please read ALL of the following download instructions BEFORE downloading the latest Quintic Ball Roll software INSTALL SHIELD program: You may need more than just the Quintic program depending on your type of computer.
• Click on the Quintic icon to the right to download your Quintic Ball Roll program onto your computer. This will begin to download the Quintic Ball Roll. Once downloaded, please run the INSTALL SHIELD program, if you have a previous version, please ADD/REMOVE via the Control Panel. Do not change or remove the Quintic security 'A' code from your pc. This is required by the new version. The Quintic licence code will still be valid...
• If you have purchased then your current Security Code A will be recognised. (If you have purchased and not received your Security Code A then please email info@quintic.com)
• Once you have successfully downloaded the required files onto your computer it is recommended that you complete the associated Quintic Tutorials (see below). These tutorials will help you learn about the different functionality of your Quintic Software.

New Features for January 2017!

• Launch Angle: The system will now calculate the 'Launch Angle' and the 'Flight Angle'. The inital launch angle is calcualted from the first two readings (Club ball interaction) and the flight angle is the point at which the ball is no longer interacting with the surface. Remember, the golf ball may be sitting in its own depression, but what effect does this have on the flight angle of the golf ball.

• Club Data: The face angle graph will now expand (double click) to maximise the graph. In addition a graphical representation of the face angle can be seen below along with the Face Angle colour regions.

• Calculation of the Address Position: The system will now calculate the 3D position of the clubface at address (face angle, shaft angle and lie angle) when you press 'Start Putt'. We have also added a self-timer for the start putt to enable a single user to analyse their address position. The address position data is displayed in the club graphics tab at the bottom of the main screen.
• Calculation of the Impact position relative to Address: The system will also calculate the face, shaft and lie angle at impact relative to your address position. This is displayed in brackets in the club graphics tab on the main screen.

• Calculation of Rifle Spin (the third component of spin) – The ball’s forward/backspin and the side-spin have historically been reported within golf. However, the third component of spin, rifle spin, has rarely been discussed. If a putt has an element of rifle spin then this is more likely to ‘knock’ the ball off-line compared to side-spin. The Quintic Ball Roll System now calculates this component of spin and displays this on the main screen.
• Calculation of the Ball’s Initial Total Spin: As we are able to display all three components of spin on the ball we are now able to calculate the ball’s initial total spin. This is also displayed on the main screen.
• Graphical display of the Ball’s three-dimensional spin: We have now added a third graphical tab at the bottom of the main screen which visually displays the three components of the ball’s initial spin, together with the ball’s total spin. We have also added the ball’s true spin axis for the total spin, which varies depending on the relationship between the three components of spin.
• Edit Initial 3D Spin: To help in the education and understanding of the three components of spin and their effect on the total spin, we have developed  Edit Initial 3D Spin which allows you to interpret how changing the three components of spin alters the ball’s spin axis. This is displayed in the Ball Data tab.

Quintic Set-up / Calibration Tutorial

• Set-up / Calibration of Quintic Ball Roll (*.Pdf document)
• Please view Calibration Tutorial Video : https://www.youtube.com/watch?v=1meYnXUVt7k

Set-up / Calibration

Quintic Calibration Error

• Set-up / Calibration Error of Quintic Ball Roll (*.Pdf document)

Calibration Error

• Quintic Ball Roll Tutorial (*.Pdf document)

Pdf Tutorial

• Quintic Key Parameters 'How to interpret the numbers...' (*.Pdf document)

Key Parameters

• Quintic Summary Range 'Blue, Green, Amber, Red' (*.Pdf document)

Summary Range

Quintic Ball Marking Video : How to put the markers on the golf ball ...

• Quintic Ball Marker Tutorial : https://www.youtube.com/watch?v=5voRbpNcDFA 

Ball Marker Tutorial

Quintic Club Marking Video : How to put the markers on the golf club ...

• Quintic Club Marker Tutorial : https://www.youtube.com/watch?v=VPBuriBiaC0

Club Marker Tutorial

Quintic Ball Roll Logo : Please right click to download QBR Logo (Save Target As)

• Quintic Ball Roll Logo (Black) / (White)